Re: poškozený root FS na točivém disku RPi.
josef dvoracek
josef.dvoracek na gmail.com
Úterý Červen 7 14:07:13 CEST 2016
Smart je ok, jen mi přijdou neobvyklé vyšší hodnoty citace typu start-stop
count, zejména v kontextu APM na maximum - to by HDD měl jet nonstop -
nepřišel s Jessie nějaký powermanagement který disk agresivně vypíná? Nebo
je to nějaký pozůstatek z předchozího umístění HDD? Neuspava se USB device?
Dne 7. 6. 2016 12:27 PM napsal uživatel "Petr Zapadlo" <zapik na email.cz>:
> > A co říká smartctl -x /dev/sda?
> > (podle toho co máte za USB - Sata adaptér tak to možná bude chtít ještě
> nějaké přepínače..)
>
>
> Výpis je delší, ale podle mě OK:
>
> udo smartctl -x /dev/sda
> smartctl 6.4 2014-10-07 r4002 [armv6l-linux-4.4.11+] (local build)
> Copyright (C) 2002-14, Bruce Allen, Christian Franke,
> www.smartmontools.org
>
> === START OF INFORMATION SECTION ===
> Device Model: SAMSUNG HM501IX
> Serial Number: C3191G74AA1JC5
> LU WWN Device Id: 5 0000f0 0aa0bc510
> Firmware Version: 2AJ10001
> User Capacity: 500 107 862 016 bytes [500 GB]
> Sector Size: 512 bytes logical/physical
> Rotation Rate: 5400 rpm
> Form Factor: 2.5 inches
> Device is: Not in smartctl database [for details use: -P showall]
> ATA Version is: ATA8-ACS T13/1699-D revision 6
> SATA Version is: SATA 2.6, 3.0 Gb/s
> Local Time is: Tue Jun 7 12:25:22 2016 CEST
> SMART support is: Available - device has SMART capability.
> SMART support is: Enabled
> AAM feature is: Disabled
> APM level is: 254 (maximum performance)
> Rd look-ahead is: Enabled
> Write cache is: Enabled
> ATA Security is: Disabled, NOT FROZEN [SEC1]
> Write SCT (Get) Feature Control Command failed: Read of ATA output
> registers not implemented [JMicron]
> Wt Cache Reorder: Unknown (SCT Feature Control command failed)
>
> === START OF READ SMART DATA SECTION ===
> SMART overall-health self-assessment test result: PASSED
>
> General SMART Values:
> Offline data collection status: (0x00) Offline data collection activity
> was never started.
> Auto Offline Data Collection:
> Disabled.
> Self-test execution status: ( 0) The previous self-test routine
> completed
> without error or no self-test has
> ever
> been run.
> Total time to complete Offline
> data collection: ( 8160) seconds.
> Offline data collection
> capabilities: (0x5b) SMART execute Offline immediate.
> Auto Offline data collection
> on/off support.
> Suspend Offline collection upon new
> command.
> Offline surface scan supported.
> Self-test supported.
> No Conveyance Self-test supported.
> Selective Self-test supported.
> SMART capabilities: (0x0003) Saves SMART data before entering
> power-saving mode.
> Supports SMART auto save timer.
> Error logging capability: (0x01) Error logging supported.
> General Purpose Logging supported.
> Short self-test routine
> recommended polling time: ( 2) minutes.
> Extended self-test routine
> recommended polling time: ( 136) minutes.
> SCT capabilities: (0x003f) SCT Status supported.
> SCT Error Recovery Control
> supported.
> SCT Feature Control supported.
> SCT Data Table supported.
>
> SMART Attributes Data Structure revision number: 16
> Vendor Specific SMART Attributes with Thresholds:
> ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
> 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 16
> 2 Throughput_Performance -OS--K 056 056 000 - 7369
> 3 Spin_Up_Time PO---K 088 088 025 - 3769
> 4 Start_Stop_Count -O--CK 048 048 000 - 52813
> 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
> 7 Seek_Error_Rate -OSR-K 252 252 051 - 0
> 8 Seek_Time_Performance --S--K 252 252 015 - 0
> 9 Power_On_Hours -O--CK 100 100 000 - 26797
> 10 Spin_Retry_Count -O--CK 252 252 051 - 0
> 11 Calibration_Retry_Count -O--CK 088 088 000 - 12988
> 12 Power_Cycle_Count -O--CK 100 100 000 - 733
> 191 G-Sense_Error_Rate -O---K 100 100 000 - 3338
> 192 Power-Off_Retract_Count -O---K 252 252 000 - 0
> 194 Temperature_Celsius -O---- 064 055 000 - 35 (Min/Max
> 17/49)
> 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
> 196 Reallocated_Event_Count -O--CK 252 252 000 - 0
> 197 Current_Pending_Sector -O--CK 252 252 000 - 0
> 198 Offline_Uncorrectable ----CK 252 252 000 - 0
> 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
> 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 201
> 223 Load_Retry_Count -O--CK 088 088 000 - 12988
> 225 Load_Cycle_Count -O--CK 001 001 000 - 1577974
> ||||||_ K auto-keep
> |||||__ C event count
> ||||___ R error rate
> |||____ S speed/performance
> ||_____ O updated online
> |______ P prefailure warning
>
> ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: 48-bit ATA commands
> not implemented [JMicron]
> Read GP Log Directory failed
>
> SMART Log Directory Version 1 [multi-sector log support]
> Address Access R/W Size Description
> 0x00 SL R/O 1 Log Directory
> 0x01 SL R/O 1 Summary SMART error log
> 0x02 SL R/O 2 Comprehensive SMART error log
> 0x06 SL R/O 1 SMART self-test log
> 0x09 SL R/W 1 Selective self-test log
> 0x80-0x9f SL R/W 16 Host vendor specific log
> 0xe0 SL R/W 1 SCT Command/Status
> 0xe1 SL R/W 1 SCT Data Transfer
>
> SMART Extended Comprehensive Error Log (GP Log 0x03) not supported
>
> SMART Error Log Version: 1
> No Errors Logged
>
> SMART Extended Self-test Log (GP Log 0x07) not supported
>
> SMART Self-test log structure revision number 1
> Num Test_Description Status Remaining
> LifeTime(hours) LBA_of_first_error
> # 1 Extended offline Completed without error 00% 26795 -
>
> SMART Selective self-test log data structure revision number 0
> Note: revision number not 1 implies that no selective self-test has ever
> been run
> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
> 1 0 0 Completed [00% left] (0-65535)
> 2 0 0 Not_testing
> 3 0 0 Not_testing
> 4 0 0 Not_testing
> 5 0 0 Not_testing
> Selective self-test flags (0x0):
> After scanning selected spans, do NOT read-scan remainder of disk.
> If Selective self-test is pending on power-up, resume after 0 minute delay.
>
> SCT Status Version: 2
> SCT Version (vendor specific): 256 (0x0100)
> SCT Support Level: 1
> Device State: Active (0)
> Current Temperature: 35 Celsius
> Power Cycle Min/Max Temperature: 30/45 Celsius
> Lifetime Min/Max Temperature: 20/63 Celsius
> Under/Over Temperature Limit Count: 0/0
>
> SCT Temperature History Version: 2
> Temperature Sampling Period: 5 minutes
> Temperature Logging Interval: 5 minutes
> Min/Max recommended Temperature: -5/80 Celsius
> Min/Max Temperature Limit: -10/85 Celsius
> Temperature History Size (Index): 128 (50)
>
> Index Estimated Time Temperature Celsius
> 51 2016-06-07 01:50 36 *****************
> ... ..( 3 skipped). .. *****************
> 55 2016-06-07 02:10 36 *****************
> 56 2016-06-07 02:15 35 ****************
> ... ..( 16 skipped). .. ****************
> 73 2016-06-07 03:40 35 ****************
> 74 2016-06-07 03:45 34 ***************
> ... ..( 5 skipped). .. ***************
> 80 2016-06-07 04:15 34 ***************
> 81 2016-06-07 04:20 32 *************
> 82 2016-06-07 04:25 31 ************
> 83 2016-06-07 04:30 32 *************
> 84 2016-06-07 04:35 32 *************
> 85 2016-06-07 04:40 32 *************
> 86 2016-06-07 04:45 33 **************
> 87 2016-06-07 04:50 30 ***********
> 88 2016-06-07 04:55 30 ***********
> 89 2016-06-07 05:00 31 ************
> 90 2016-06-07 05:05 33 **************
> 91 2016-06-07 05:10 36 *****************
> 92 2016-06-07 05:15 37 ******************
> 93 2016-06-07 05:20 38 *******************
> 94 2016-06-07 05:25 39 ********************
> 95 2016-06-07 05:30 39 ********************
> 96 2016-06-07 05:35 39 ********************
> 97 2016-06-07 05:40 40 *********************
> 98 2016-06-07 05:45 41 **********************
> 99 2016-06-07 05:50 41 **********************
> 100 2016-06-07 05:55 41 **********************
> 101 2016-06-07 06:00 42 ***********************
> 102 2016-06-07 06:05 42 ***********************
> 103 2016-06-07 06:10 39 ********************
> 104 2016-06-07 06:15 40 *********************
> 105 2016-06-07 06:20 41 **********************
> 106 2016-06-07 06:25 42 ***********************
> ... ..( 3 skipped). .. ***********************
> 110 2016-06-07 06:45 42 ***********************
> 111 2016-06-07 06:50 40 *********************
> 112 2016-06-07 06:55 39 ********************
> 113 2016-06-07 07:00 38 *******************
> ... ..( 7 skipped). .. *******************
> 121 2016-06-07 07:40 38 *******************
> 122 2016-06-07 07:45 37 ******************
> 123 2016-06-07 07:50 37 ******************
> 124 2016-06-07 07:55 36 *****************
> 125 2016-06-07 08:00 36 *****************
> 126 2016-06-07 08:05 35 ****************
> ... ..( 5 skipped). .. ****************
> 4 2016-06-07 08:35 35 ****************
> 5 2016-06-07 08:40 37 ******************
> 6 2016-06-07 08:45 40 *********************
> 7 2016-06-07 08:50 41 **********************
> 8 2016-06-07 08:55 42 ***********************
> 9 2016-06-07 09:00 43 ************************
> 10 2016-06-07 09:05 43 ************************
> 11 2016-06-07 09:10 44 *************************
> ... ..( 2 skipped). .. *************************
> 14 2016-06-07 09:25 44 *************************
> 15 2016-06-07 09:30 45 **************************
> 16 2016-06-07 09:35 45 **************************
> 17 2016-06-07 09:40 45 **************************
> 18 2016-06-07 09:45 44 *************************
> 19 2016-06-07 09:50 45 **************************
> 20 2016-06-07 09:55 44 *************************
> 21 2016-06-07 10:00 45 **************************
> ... ..( 5 skipped). .. **************************
> 27 2016-06-07 10:30 45 **************************
> 28 2016-06-07 10:35 43 ************************
> 29 2016-06-07 10:40 41 **********************
> 30 2016-06-07 10:45 40 *********************
> 31 2016-06-07 10:50 39 ********************
> 32 2016-06-07 10:55 38 *******************
> 33 2016-06-07 11:00 37 ******************
> 34 2016-06-07 11:05 37 ******************
> 35 2016-06-07 11:10 37 ******************
> 36 2016-06-07 11:15 36 *****************
> ... ..( 4 skipped). .. *****************
> 41 2016-06-07 11:40 36 *****************
> 42 2016-06-07 11:45 35 ****************
> 43 2016-06-07 11:50 35 ****************
> 44 2016-06-07 11:55 36 *****************
> 45 2016-06-07 12:00 35 ****************
> 46 2016-06-07 12:05 36 *****************
> 47 2016-06-07 12:10 35 ****************
> ... ..( 2 skipped). .. ****************
> 50 2016-06-07 12:25 35 ****************
>
> Write SCT (Get) Error Recovery Control Command failed: Read of ATA output
> registers not implemented [JMicron]
> SCT (Get) Error Recovery Control command failed
>
> Device Statistics (GP/SMART Log 0x04) not supported
>
> ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: 48-bit ATA commands
> not implemented [JMicron]
> Read SATA Phy Event Counters failed
>
>
> _______________________________________________
> HW-list mailing list - sponsored by www.HW.cz
> Hw-list na list.hw.cz
> http://list.hw.cz/mailman/listinfo/hw-list
>
------------- další část ---------------
HTML příloha byla odstraněna...
URL: <http://list.hw.cz/pipermail/hw-list/attachments/20160607/aa785d2b/attachment.html>
Další informace o konferenci Hw-list