Arduino nano s fake FTDI - spatne provedeny unbrick
Petr Simek
psimek na jcu.cz
Středa Září 26 11:40:15 CEST 2018
On Wed, 26 Sep 2018, Peter Berec wrote:
Jenze aby se dal FT_prog pouzit musi byt napred nahozeny USB driver
a ten se nenahodi kdyz nesedi VID/PID .
*------------------------------------------------------------------------*
| Petr Simek APS JU |
| psimek na jcu.cz |
*------------------------------------------------------------------------*
> A ja len doplnim vypis helpu prislusnej utility:
>
> ft232r_prog: version 1.25, by Mark Lord.
>
> Usage: ft232r_prog [<arg> <val>]..
>
> where <arg> must be any of:
> --help # (show this help text)
> --dump # (dump eeprom settings to stdout))
> --verbose # (show debug info and raw eeprom contents)
> --save # (save original eeprom contents to file)
> --restore # (restore initial eeprom contents from file)
> --cbus0
> [TxDEN|PwrEn|RxLED|TxLED|TxRxLED|Sleep|Clk48|Clk24|Clk12|Clk6|IO|WR|RD|RxF]
> --cbus1
> [TxDEN|PwrEn|RxLED|TxLED|TxRxLED|Sleep|Clk48|Clk24|Clk12|Clk6|IO|WR|RD|RxF]
> --cbus2
> [TxDEN|PwrEn|RxLED|TxLED|TxRxLED|Sleep|Clk48|Clk24|Clk12|Clk6|IO|WR|RD|RxF]
> --cbus3
> [TxDEN|PwrEn|RxLED|TxLED|TxRxLED|Sleep|Clk48|Clk24|Clk12|Clk6|IO|WR|RD|RxF]
> --cbus4
> [TxDEN|PwrEn|RxLED|TxLED|TxRxLED|Sleep|Clk48|Clk24|Clk12|Clk6|IO|WR|RD|RxF]
> --manufacturer <string> # (new USB manufacturer string)
> --product <string> # (new USB product name string)
> --old-serial-number <string> # (current serial number of device to be
> reprogrammed)
> --new-serial-number <string> # (new USB serial number string)
> --self-powered [on|off] # (self powered)
> --max-bus-power <number> # (max bus current in milli-amperes)
> --high-current-io [on|off] # (enable high [6mA @ 5V] drive current on
> CBUS pins)
> --suspend-pull-down [on|off] # (force I/O pins into logic low state on
> suspend)
> --old-vid <number> # (current vendor id of device to be reprogrammed,
> eg. 0x0403)
> --old-pid <number> # (current product id of device to be
> reprogrammed, eg. 0x6001)
> --new-vid <number> # (new/custom vendor id to be programmed)
> --new-pid <number> # (new/custom product id be programmed)
> --invert_txd Inverts the current value of TXD
> --invert_rxd Inverts the current value of RXD
> --invert_rts Inverts the current value of RTS
> --invert_cts Inverts the current value of CTS
> --invert_dtr Inverts the current value of DTR
> --invert_dsr Inverts the current value of DSR
> --invert_dcd Inverts the current value of DCD
> --invert_ri Inverts the current value of RI
>
> P.
Další informace o konferenci Hw-list