KiCad a Seeedstudio

[Zuffa Jan]

Dril 0.3 je minimum, Annular ring je dobre popisany tu:

https://github.com/dren-dk/HAL900/wiki/Quirks-of-PCB-manufacturing-at-ITead

Samozrejme hra ulohu indukcnost a  kapacita via ale realne tak 100MHz+
Ja som sa pri navrhu musel uspokojit s via co najmensimi (predsa zaberaju nejaky ten priestor)
napriek tomu som nesiel pod 0.4 / 0.8

j.

-----Original Message-----
From: Hw-list [mailto:hw-list-bounces na list.hw.cz] On Behalf Of iko
Sent: Wednesday, May 18, 2016 9:54 AM
To: HW-news
Subject: Re: KiCad a Seeedstudio

Tak uz to zobrazuje dobre, len stale pise
    Gerber file cannot be identified.

Este otazocka, prekovy sa zvyknu ake davat priemery (Via Dia a Via Drill) ?

On 05/18/2016 09:06 AM, Zuffa Jan wrote:
> Zdravim,
>
> Diery prekovov tam nie je vidiet preto, ze su v pcbname.txt takze to 
> je OK.  A chyba je preto, ze v pcbname.txt je diera (niekolko) ktora 
> je mimo hranic  vrsvty .gtl alebo nemate nakreslene pcb boudaries co 
> by malo byt edge.cuts. Este ma napada ze niektore hranicne ciary 
> (boundaries)  nie su celkom spojene
>
> j.
>
> -----Original Message-----
> From: Hw-list [mailto:hw-list-bounces na list.hw.cz] On Behalf Of iko
> Sent: Wednesday, May 18, 2016 8:44 AM
> To: HW-news
> Subject: Re: KiCad a Seeedstudio
>
> Aha, zelena plocha uz je ok (premenoval som drl na txt), aj diery mi zobrazuje, ale stale hlaska:
>     Gerber file cannot be identified.
>     The bounds of copper-top do not overlap the bounds of drill-01.
>
> A nevidim tam diery prekovov.
>
> On 05/18/2016 08:36 AM, iko wrote:
>> Zdravim,
>>
>> nemate niekto postup, ako objednat DPS zo seeedstudio? Ide o 2vrstvovy.
>> Vyrobil som tieto subory:
>>     pcbname.gbl
>>     pcbname.gbo
>>     pcbname.gbs
>>     pcbname.gm1
>>     pcbname.gtl
>>     pcbname.gto
>>     pcbname.gts
>>
>> a DRL subory mi spravilo 2
>>     pcbname.drl
>>     pcbname-NPTH.drl
>>
>> Gerber viewer co maju na stranke mi na to stale hadze chyby:
>>     Gerber file cannot be identified.
>>     The bounds of copper-top do not overlap the bounds of drill-02.
>>
>> Aj zobrazenie je nejake divne, zelena plocha na DPS je len maly 
>> stvorcek, nie cez celu dosku, zrejme to tak nema byt. Co mam zaklikat 
>> v KiCade aby to bolo OK?
>>
>> Screenshot dialogov:
>> https://dl.dropboxusercontent.com/u/3827856/kicad/Screenshot-61.png
>> https://dl.dropboxusercontent.com/u/3827856/kicad/Screenshot-62.png
>>
>> Vdaka...
>>
> --
> iko
>
> Počítač bez Windows je ako kakao bez kečupu.
>
> _______________________________________________
> HW-list mailing list  -  sponsored by www.HW.cz Hw-list na list.hw.cz 
> http://list.hw.cz/mailman/listinfo/hw-list
> _______________________________________________
> HW-list mailing list  -  sponsored by www.HW.cz Hw-list na list.hw.cz 
> http://list.hw.cz/mailman/listinfo/hw-list

--
iko

Počítač bez Windows je ako kakao bez kečupu.


_______________________________________________
HW-list mailing list  -  sponsored by www.HW.cz Hw-list na list.hw.cz http://list.hw.cz/mailman/listinfo/hw-list