Chyba u MPLAB 8.7

[Michal Gregor]

CONFIG_M CODE    ;Nastavení procesoru
  dw  _CP_ALL & _WDT_ON & _BODEN_ON & _PWRTE_ON & _HS_OSC & _WRT_ENABLE_OFF 
& _LVP_OFF & _CPD_ON

Chyba:
Error[113] C:\A\MPLAB\ASEMBLER\KOM8_31\KOM8_31.ASM 57 : Symbol not 
previously defined (_CP_ALL)
Halting build on first failure as requested.


Detail z inc souboru:
;----- CONFIG Options --------------------------------------------------
_LP_OSC              EQU  H'3FFC'    ; LP oscillator
_XT_OSC              EQU  H'3FFD'    ; XT oscillator
_HS_OSC              EQU  H'3FFE'    ; HS oscillator
_RC_OSC              EQU  H'3FFF'    ; RC oscillator

_WDT_OFF             EQU  H'3FFB'    ; WDT disabled
_WDT_ON              EQU  H'3FFF'    ; WDT enabled

_PWRTE_ON            EQU  H'3FF7'    ; PWRT enabled
_PWRTE_OFF           EQU  H'3FFF'    ; PWRT disabled

_CP_All              EQU  H'0FCF'    ; 0000h to 0FFFh code protected
_CP_HALF             EQU  H'1FDF'    ; 0800h to 0FFFh code protected
_CP_UPPER_256        EQU  H'2FEF'    ; 0F00h to 0FFFh code protected
_CP_OFF              EQU  H'3FFF'    ; Code protection off

_BODEN_OFF           EQU  H'3FBF'    ; BOR disabled
_BODEN_ON            EQU  H'3FFF'    ; BOR enabled

_LVP_OFF             EQU  H'3F7F'    ; RB3 is digital I/O, HV on MCLR must 
be used for programming
_LVP_ON              EQU  H'3FFF'    ; RB3/PGM pin has PGM function; 
low-voltage programming enabled

_CPD_ON              EQU  H'3EFF'    ; Data EEPROM memory code-protected
_CPD_OFF             EQU  H'3FFF'    ; Code Protection off

_WRT_ENABLE_OFF      EQU  H'3DFF'    ; Unprotected program memory may not be 
written to by EECON control
_WRT_ENABLE_ON       EQU  H'3FFF'    ; Unprotected program memory may be 
written to by EECON control

_DEBUG_ON            EQU  H'37FF'    ; In-Circuit Debugger enabled, RB6 and 
RB7 are dedicated to the debugger
_DEBUG_OFF           EQU  H'3FFF'    ; In-Circuit Debugger disabled, RB6 and 
RB7 are general purpose I/O pins

Dela to jen  _CP_ALL, kdyz ho nahradim cislem H'0FCF' tak to zkompilovat 
jde. Vypada to ze nova verze asembleru _CP_ALL nejak blokuje.
(  dw   H'0FCF' & _WDT_ON & _BODEN_ON & _PWRTE_ON & _HS_OSC & 
_WRT_ENABLE_OFF & _LVP_OFF & _CPD_ON )

Michal Gregor


----- Original Message ----- 
From: "j s" <jarin.hw na gmail.com>
To: "HW-news" <hw-list na list.hw.cz>
Sent: Friday, June 24, 2011 1:35 PM
Subject: Re: Chyba u MPLAB 8.7


Ja si myslim, ze chyba je na riadku cislo 43.

J.S.


2011/6/24 Michal Gregor <a2x1nptda8 na email.cz>:
> Nahral jsem si novy MPLAB v 8.7 a prestal mi fungovat stary projekt - pri
> kompilaci to hlasi neznama promenna : _CP_ALL
> Pritom v inc souboru je. Nevite cim to je?
>
> Michal Gregor
> _______________________________________________
> HW-list mailing list - sponsored by www.HW.cz
> Hw-list na list.hw.cz
> http://list.hw.cz/mailman/listinfo/hw-list
>
_______________________________________________
HW-list mailing list  -  sponsored by www.HW.cz
Hw-list na list.hw.cz
http://list.hw.cz/mailman/listinfo/hw-list