leptanie nereze
michal lukac
michal.lukac@fstroj.utc.sk
Středa Březen 2 16:39:00 CET 2005
ale potreboval by som to "homemade" a laser doma nemam.....:)
----- Original Message -----
From: <turby@chips.cz>
To: "HW-news" <hw-list@list.hw.cz>
Sent: Wednesday, March 02, 2005 3:15 PM
Subject: Re: leptanie nereze
Zdravim,
v tom pripade se bezne pouziva gravirovani laserem...
--
turby@chips.cz
2. března 2005, 15:04:57, napsal jste:
> No prave na panel to nema byt.....na privesky, a tomu farbeniu som sa
> chcel
> vyhnut.
> ale aj tak dik za odpovede..... sksusim to vyleptat v Fe2Cl3
> hodne o chemickom dokoncovani je na www.finishing.com ak by to niekoho
> zaujimalo....
> napr. http://finishing.com/72/76.shtml
> Electrolitic colour for SS(Ni/Cr 18/8):
> H2SO4........1 lit
> Na2Cr2O7......7,5 gm (ma toto nejaky nazov?)
> 7o-95 C/o,o6 A/dm2-1,3V,object=anode,cathode=lead -> ale tomuto moc
> nerozumiem: 7o-95 C/o ...:(((
> Colour sequence:brown-blue-yellow-redish brown-purple-green. -> a tomuto
> tiez... :((
> alebo pre leptanie napr......
> --------------------------------
> Well you can use 1:3 solution of HCl with water and use a rectifier with
> low
> D.C. current of 6 volts with s.s the cathode and the work piece as anode
> then check for the depth required. Good luck.
> --------------------------------
> etching stainless steel
> for microstructure use marbles reagent
> 200 cm of water with 40 g of copper(11) sulphate in 200 cm of HCl (35%)
> for stock removal use a ferric chloride mix consisting of
> 11 gallons of 60% ferric chloride
> 10 gallons of HCL
> and 4 gallons of nitric but be careful ferric chloride is a pitting
> agent
> M.
> ----- Original Message -----
> From: <turby@chips.cz>
> To: "HW-news" <hw-list@list.hw.cz>
> Sent: Wednesday, March 02, 2005 1:31 PM
> Subject: Re: leptanie nereze
> Zdravim,
> jeste je mozne panel gravirovat jak mechanicky tak i laserem.
> Pripadne pak vyplnit barvou. Oboje vypada pomerne dobre.
> Hledejte "gravirovani laser"
> --
> turby@chips.cz
> 2. března 2005, 11:19:08, napsal jste:
>> Da se leptat silnou kyselinou dusicnou (cca 95%) Problem je, ze
>> bezne sezenete nejvic nejakych 65% a priprava silnejsi je dost
>> nechutna zalezitost. A taky to nefungovalo vzdy, asi neni nerez jako
>> nerez. Osvedcilo se mi piskovani. Nechate si motiv vyriznout z
>> obycejne reklamni folie a v kazdem lepsim sklenarstvi Vam to na
>> pockani vypiskuji. Vysledek je mnohem kontrastnejsi nez leptani,
>> pripadne jde do vypiskovanych ploch "vetrit" nejaka tmavsi barva.
>>> > Vedel by mi niekto prosim poradit v com by sa dala najlepsie leptat
>>> > nerez?
>> _______________________________________________
>> HW-list mailing list - sponsored by www.HW.cz
>> Hw-list@list.hw.cz
>> http://list.hw.cz/mailman/listinfo/hw-list
> _______________________________________________
> HW-list mailing list - sponsored by www.HW.cz
> Hw-list@list.hw.cz
> http://list.hw.cz/mailman/listinfo/hw-list
> _______________________________________________
> HW-list mailing list - sponsored by www.HW.cz
> Hw-list@list.hw.cz
> http://list.hw.cz/mailman/listinfo/hw-list
_______________________________________________
HW-list mailing list - sponsored by www.HW.cz
Hw-list@list.hw.cz
http://list.hw.cz/mailman/listinfo/hw-list
Další informace o konferenci Hw-list