Brd cut/paste RE: Eagle - presun casti schemy ->t ovladani SW

[APa]

To asi ne, to bude nejaky anachronismus z dob "pred Windows", podobne jako
AutoCAD ma prikazovou radku a trochu neintuitivni ovladani. 

> -----Original Message-----
> From: hw-list-bounces@list.hw.cz 
> [mailto:hw-list-bounces@list.hw.cz] On Behalf Of Michal HW
> Sent: Thursday, December 15, 2005 4:48 PM
> To: HW-news
> Subject: Re: Brd cut/paste RE: Eagle - presun casti schemy 
> ->t ovladani SW
> 
> Nejen Eagle, ja nevim proc se nekteri programatori tak zurive 
> zuby nechty brani klavesovym zkratkam a ergonomickemu 
> ovladani. Nedela to vyvojove prostredi? (Delfi,C+++++ atd) Michal
> 
> ----- Original Message -----
> From: "APa" <navrhpcb@centrum.cz>
> To: "'HW-news'" <hw-list@list.hw.cz>
> Sent: Thursday, December 15, 2005 4:24 PM
> Subject: RE: Brd cut/paste RE: Eagle - presun casti schemy na 
> druhy list
> 
> 
> Panecku, to jsem nevedel, ten eagle psali tatari jeste kdyz 
> nebyl Windows,
> ze? :-))
> 
> > -----Original Message-----
> > From: hw-list-bounces@list.hw.cz
> > [mailto:hw-list-bounces@list.hw.cz] On Behalf Of Marek Sembol
> > Sent: Thursday, December 15, 2005 4:08 PM
> > To: HW-news
> > Subject: Re: Brd cut/paste RE: Eagle - presun casti schemy na
> > druhy list
> >
> > nejdriv copy a az pak kliknout na soucastku pokud chcete
> > blok, nesmite pres copy ale pres cut (kupodivu to nevyjme ze
> > schematu/bordu, ale jen strci do bufferu). Ale zas. nejdriv
> > cut a pak kliknout (levym soucastka, pravym grupa) co :) Marek
> >
> > On 12/15/05, APa <navrhpcb@centrum.cz> wrote:
> > > Z menu edit vyperu (pri vybrane soucastce) copy a pak
> > paste, odpoved
> > > vzdy
> > > byla:
> > >
> > > Paste buffer is empty
> > >
> > > > -----Original Message-----
> > > > From: hw-list-bounces@list.hw.cz
> > > > [mailto:hw-list-bounces@list.hw.cz] On Behalf Of Kamil Rezac
> > > > Sent: Thursday, December 15, 2005 3:46 PM
> > > > To: HW-news
> > > > Subject: Re: Brd cut/paste RE: Eagle - presun casti
> > schemy na druhy
> > > > list
> > > >
> > > > Vyberu blok a pak z toolbaru (po leve strane) pouziju 
> cut a paste.
> > > > Klavesove zkratky to pokud vim nema (ale popravde receno,
> > v brd jsem
> > > > to nikdy nedelal)
> > > >
> > > > KR
> > > >
> > > > On 12/15/05, APa <navrhpcb@centrum.cz> wrote:
> > > > > Mohu se zeptat, jak na BRD oznacim, zkopiruji a pastnu
> > soucastku?
> > > > > Klasicke Windowsi Ctrl+C/Ctrl+V mi jaxi nechodi :-/
> > > > _______________________________________________
> > > > HW-list mailing list  -  sponsored by www.HW.cz
> > Hw-list@list.hw.cz
> > > > http://list.hw.cz/mailman/listinfo/hw-list
> > > >
> > >
> > > _______________________________________________
> > > HW-list mailing list  -  sponsored by www.HW.cz Hw-list@list.hw.cz
> > > http://list.hw.cz/mailman/listinfo/hw-list
> > >
> > _______________________________________________
> > HW-list mailing list  -  sponsored by www.HW.cz
> > Hw-list@list.hw.cz http://list.hw.cz/mailman/listinfo/hw-list
> >
> 
> _______________________________________________
> HW-list mailing list  -  sponsored by www.HW.cz
> Hw-list@list.hw.cz
> http://list.hw.cz/mailman/listinfo/hw-list
> 
> _______________________________________________
> HW-list mailing list  -  sponsored by www.HW.cz
> Hw-list@list.hw.cz
> http://list.hw.cz/mailman/listinfo/hw-list
>