<html><body>A potom to cuca 14A, alebo sa vam nerozbehne invertor... No naozaj neviem.<br><br>A.<br><br><br>On Tue, 25 Jan 2011 19:44:22 +0100<br> "andrej jancura" <hw_aj@zoznam.sk> wrote:<br>> Ja fakt neviem, zeby to bolo 14A z jednej faze????? Na zaciatku mate <br>>vsetko skratovane, ale asi sa mylim...<br>> <br>> A.<br>> <br>> <br>> <br>> On Tue, 25 Jan 2011 19:34:04 +0100<br>> "aze" wrote:<br>>> Čím by se ty žárovky měly upálit? Jak se protlačí ze sítě 200W <br>>>žárovkou 4,5A?<br>>> AZE<br>>> <br>>> ----- Original Message ----- <br>>> From: andrej jancura <br>>> To: HW-news <br>>> Sent: Tuesday, January 25, 2011 7:24 PM<br>>> Subject: Re: SoftStart na 3f s prikonem kolem 10kW<br>>> <br>>> <br>>> Po tazkych uvahach, ktore zrusil moj webovy klient, by som tam dal <br>>>tr310 mozno tr320, 100Ohm v IP20... V mojej uvahe tie ziarovky <br>>>spolahlivo upal
ite, kedze 200W a 230V nie je ani 1A, a vy tam mate na <br>>>fazu minimalne 4,5A, kedze vam to berie 14A kontinualne, teda v <br>>>pulznom este viac. Je to totiz len stredna hodnota. Potom casove rele <br>>>elko a stykac a malo by byt vymalovane... Samozrejme v setko bez <br>>>zaruky a ujme na majetku!!!<br>>> <br>>> A.<br>>> <br>>> <br>>> <br>>> On Tue, 25 Jan 2011 16:31:27 +0100<br>>> "HW CNCnet.info" wrote:<br>>> > aspon blokove schema jsem dal <br>>> >sem...http://www.cncnet.info/galery/mig/mig.gif<br>>> > <br>>> > jde o Jasic 250 MIG<br>>> > <br>>> > -- <br>>> > S pozdravem<br>>> > <br>>>======================================================================<br>>> > Radek Vicek<br>>> > <br>>>======================================================================<br>>> > http://www.cn
cnet.info - problematika CNC a automatizace<br>>> > http://www.jakj evenku.info - webová meteostanice<br>>> > <br>>> > Dne 25.1.2011 16:09, HW CNCnet.info napsal(a):<br>>> >> Netvrdim, ze by to nebylo nejspravnejsi, ale ta svarecka jeste <br>>>ani<br>>> >> nebezela a je v zaruce. Sice na ni nejsou plomby, ale take to <br>>> neni <br>>> >>PC<br>>> >> zdroj - cast soucastek je v nejake Al ingotu s vetrakem, ktery<br>>> >> vymontovat znamena rozebrat v podstate celou svarecku. A prurezy <br>>> >>vodicu<br>>> >> take nejsou zanedbatelne - rozhodne to nepujde rozebrat treba <br>>>tak <br>>> >>aby<br>>> >> nebylo videt ze se v tom nekdo vrtal.<br>>> >><br>>> > _______________________________________________<br>>> > HW-list mailing list - sponsored by www.HW.cz<br>>> > Hw-list
@list.hw.cz<br>>> > http://list.hw.cz/mailman/listinfo/hw-list<br>>> <br>>> <br>>> __________ NOD32 5818 (20110125) Information __________<br>>> <br>>> This message was checked by NOD32 antivirus system.<br>>> http://www.eset.com<br>>> <br>>> <br>>> <br>>> ------------------------------------------------------------------------------<br>>> <br>>> <br>>> _______________________________________________<br>> > HW-list mailing list - sponsored by www.HW.cz<br>>> Hw-list@list.hw.cz<br>>> http://list.hw.cz/mailman/listinfo/hw-list<br>>> <br>>> <br>>> <br>>> __________ NOD32 5818 (20110125) Information __________<br>>> <br>>> This message was checked by NOD32 antivirus system.<br>>> http://www.eset.com<br>> <br></hw_aj@zoznam.sk></body></html>